Write a comment
Spacecraft have long used heat shields for protection during entry into planetary atmospheres. Future missions to the outer solar system will need more sophisticated materials than currently exist. The extreme heating conditions needed to study new shield materials are, however, very difficult to achieve experimentally on Earth.
Scientists working at the DIII-D National Fusion Facility at Spacecraft have long used heat shields for protection during entry into planetary atmospheres. Future missions to the outer solar system will need more sophisticated materials than currently exist. The extreme heating conditions needed to study new shield materials are, however, very difficult to achieve experimentally on Earth.
Scientists working at the DIII-D National Fusion Facility at General Atomics (GA) recently developed an innovative approach that uses the conditions inside a fusion reactor for testing heat shield materials.
During high-speed atmospheric entries of up to 100,000 miles per hour, such as those required in missions to the Solar System's gas giants, the atmospheric gas surrounding the spacecraft turns into plasma (a mixture of ions and electrons) and spacecraft temperatures increase to more than 10,000 F. To protect the scientific payload, the heat shield material burns (or ablates) in a controlled manner, which pulls the excess heat away from the core of the spacecraft.
Past heat shield testing approaches using lasers, plasma jets, and hypervelocity projectiles suffered from the problem that no single method could simulate the exact heating conditions present during a high-speed atmospheric entry. Consequently, past models of heat shield behavior have sometimes over- or under-predicted ablation of the heat shield, with potentially disastrous results.
The experiments at DIII-D demonstrated that the hot plasma created by a fusion reactor during operation offers a novel and potentially improved way of modeling heat shield behavior, especially for entries into Venus or the gas giants.
"Certain regions of the plasma in DIII-D closely approximate the conditions created when heat shields impact planetary atmospheres at extreme velocities," said Dr. Dmitri Orlov of the University of California San Diego, who led the multi-institutional team. "Our intent with these experiments was to leverage both these conditions and DIII-D's rich suite of diagnostic instruments to develop a more accurate model of heat shield behavior."
Most experiments conducted at DIII-D are intended to explore the physics basis for fusion energy. An existing system at DIII-D, known as the Divertor Materials Evaluation System (DiMES), is designed to test materials for future reactors. DiMES can expose test samples to various plasma conditions as well as launch pellets of test material through the plasma.
Dr. Orlov and Dr. Eva Kostadinova of Auburn University, working with a team of scientists, undergraduate, and graduate students, used DiMES to study the ablation rates of carbon samples under extreme conditions and refine predictive models for carbon-based heat shield behavior.
These experiments were conducted under the auspices of the Frontier Sciences program, funded by the U.S. Department of Energy, to provide access to DIII-D and other DOE-funded facilities to the broader physics community.
"DIII-D features relatively long plasma discharges with well-controlled stable conditions at the edge, where the heat flux and the flow speed are similar to those experienced during atmospheric entries," said Dr.
Kostadinova. "This allowed us to simulate some of the most extreme conditions heat shields have experienced, such as the entry of the Galileo probe to Jupiter's atmosphere, without the need to launch our test samples at high velocities."
Because DIII-D is one of the most flexible and highly instrumented fusion reactors in the world, the team was able to gather a range of valuable data on the behavior of the samples.
By using scaling techniques, they extrapolated the results to larger projectiles and longer exposures, which allowed for comparison with experimental data from previous space flight missions and other on-ground testing facilities. The results offer considerable promise to develop the advanced heat shield materials necessary for planned missions to Venus and the Jovian moons.
Related Links
General Atomics
Powering The World in the 21st Century at Energy-Daily.com
|
| Tweet |
| Thanks for being here;
We need your help. The SpaceDaily news network continues to grow but revenues have never been harder to maintain. With the rise of Ad Blockers, and Facebook - our traditional revenue sources via quality network advertising continues to decline. And unlike so many other news sites, we don't have a paywall - with those annoying usernames and passwords. Our news coverage takes time and effort to publish 365 days a year. If you find our news sites informative and useful then please consider becoming a regular supporter or for now make a one off contribution. | ||
| SpaceDaily Contributor
$5 Billed Once credit card or paypal |  | SpaceDaily Monthly Supporter
$5 Billed Monthly paypal only |
Integrating hot cores and cool edges in fusion reactors
Pittsburgh PA (SPX) Nov 15, 2021
Future fusion reactors have a conundrum: maintain a plasma core that is hotter than the surface of the sun without melting the walls that contain the plasma. Fusion scientists refer to this challenge as "core-edge integration." Researchers working at the DIII-D National Fusion Facility at General Atomics have recently tackled this problem in two ways: the first aims to make the fusion core even hotter, while the second focuses on cooling the material that reaches the wall. Protecting the pla ... read more